High-quality case accessories
Alaşım
● Free disassembly & assembly
● Full metal body, resistant to rough transportation
● Diode Laser Hair Removal Machine
Machine display
Component display
① Base
② Front plate
③ Handle
④ Top plate
⑤ Right plate
⑥ Screen
⑦ Left plate
⑧ Back plate
⑨ Box
⑩ Front small plate
⑪ Handpiece holder
| ① | Base |
| ② | Front plate |
| ③ | Halletmek |
| ④ | Top plate |
| ⑤ | Right plate |
| ⑥ | Ekran |
| ⑦ | Left plate |
| ⑧ | Back plate |
| ⑨ | Box |
| ⑩ | Front small plate |
| ⑪ | Handpiece holder |
Assembly order
| 1. Install the base |
|---|
| Please use M4 screws for the following installations. |
| As shown, align the 4 screw holes on both sides of the base with the screw holes of the machine core one by one, first fix them all in place with screws loosely, and then tighten the screws separately. |
| 2. Install the front plate |
|---|
| Remove the two wires with exposed metal wires on the upper part of the machine core, straighten the wires, and place them under the washers of the two screws of the yellow indicator light (the top of the front plate), ensure good contact, and tighten the screws. |
| Insert the blue wire with the U-shaped metal sheet into the hole marked 4 of the key switch, and insert the red wire with the U-shaped metal sheet into the hole marked 1 of the emergency switch, ensure good contact, and tighten the screws. |
| Align the 6 screw holes on both sides of the edge of the front plate with the screw holes on the vertical iron frame of the machine core, and also align the two screw holes on the bottom of the front plate and the machine core. After all the above screw holes are loosely fixed in place with screws, tighten the screws separately. Not: The top 2 screws need to be fixed with a nut on the inside of the frame. |
| 3. Install the handle |
|---|
| Not: The protruding parts on both sides of the handle face downward. Align the screw holes on the lower sides of the handle with the two screw holes at the top of the two sides of the front plate, and fix them all in place loosely with screws. |
| 4. Install the upper plate |
|---|
| Put the upper plate in the appropriate position, align the screw holes on the upper sides of the handle with the two screw holes at the bottom of the two sides of the upper plate, and fix them all in place loosely with screws. Tighten the 4 screws on both sides of the handle separately. |
| 5. Install the right plate |
|---|
| Align the 3 screw holes on the left side of the right plate with the 3 screw holes in the middle of the installed upper plate and the front plate, first fix them all in place loosely with screws, and then tighten them separately. |
| Align the 3 screw holes on the right side of the right plate with the 3 screw holes on the machine core, first fix them all in place loosely with screws, and then tighten them separately. (If you have difficulty aligning the screw holes, you can use a crowbar to insert the gap between the right plate and the frame to assist in positioning.) |
| 6. Install the screen |
|---|
| Put the monitor cable into the hole in front of the upper plate. Align the four screw holes on the two hinges of the monitor with the four screw holes on the upper plate one by one, first fix them all in place with screws loosely, and then tighten them separately. |
| Insert the other end of the monitor cable into the jack on the left side of the main control board as shown in the picture/video, and arrange and place the cables properly. |
| 7. Install the left plate |
|---|
| The installation method is the same as the right plate. |
| 8. Install the back plate |
|---|
| Connect the blue wire jack on the machine core with the blue plug on the back plate, and the red wire jack with the red plug. After arranging the wires in the case, close the back plate. |
| Align the 9 screw holes on the back plate with the 9 screw holes on the installed body one by one, first fix them all in place with screws loosely, and then tighten them separately. |
| 9. Install the box |
|---|
| With the bottom of the box facing down, align the 4 screw holes of the box with the 4 screw holes of the top plate one by one, first fix them all in place with screws loosely, and then tighten them separately. |
| 10. Install the front small plate |
|---|
| With the paint surface of the front small board facing outward, align the 4 screw holes of the front small board with the 4 screw holes below the front board one by one, first fix them all in place with screws loosely, and then tighten them separately. |
| 11. Install the handpiece holder |
|---|
| Insert the metal rod of the handpiece holder into the hole behind the left plate, rotate the metal rod, and adjust it to the required angle. First fix the two screw holes in place with screws loosely, and then tighten them separately. |
Assembly video tutorial
